- #Dante virtual soundcard license for how many computers software
- #Dante virtual soundcard license for how many computers professional
- #Dante virtual soundcard license for how many computers windows
So if there is a bottleneck somewhere in the network, then the data from true Dante devices is preferred, as long as QoS is set up accordingly on all switches. Unfortunately, a QoS / DSCP tag is not attached as it is the case with all true Dante devices.
#Dante virtual soundcard license for how many computers windows
And Windows has control over the hardware and sends the data on to the network card. Since the Dante Virtual Soundcard is only a Windows service, the data packets are transferred to Windows. In the event of a bottleneck, the switch knows which data to transport first and which data may be swallowed. Clock data have the highest priority, audio data the second highest. But if you have already dealt with your network and have set up a security mechanism such as Quality of Service (QoS) with great attention to detail in all switches, then this information may be relevant for you after all.ĭante devices tag their outgoing packets with a so-called DSCP tag with regard to their importance. It sounds very technical and hardly relevant to everyday life. 2) Outgoing flows do not have a QoS / DSCP tag And unfortunately this option is not available with the DVS and cannot be purchased or configured on request.
#Dante virtual soundcard license for how many computers professional
It is not without reason, however, that all professional Dante devices have two network ports so that an audio connection does not get interrupted in the event of a network problem. And just for fun, recording 64 channels at a concert so that you have some material at home to mix with works wonderfully only with the primary network. Because playing a little background music is also possible through one network. Depending on the purpose, you will not mind this or you will not notice it at all. While two network cards can be configured in the Dante Controller for the primary and secondary network, there is unfortunately no such option in the Dante Virtual Soundcard. In order to show you the downsides and enable you to make a solid decision, here are my five not so pleasant points about the DVS: 1) No Redundancy Nonetheless, there are a few points that are not entirely obvious if you haven't used them before.
#Dante virtual soundcard license for how many computers software
I primarily use it as an interface between my calibration software and the microphone interface or for feeding into the respective sound system.īut even in everyday (sound) life, it can be used to play music into the system, or record a few channels, or intentionally generate 64 channels of Dante multicast traffic to test the network! I can warmly recommend DVS for the few dollars and use it myself every day. That's why I have the Dante Virtual Soundcard installed on each of my PCs. Unfortunately, the price jump is huge, especially since both solutions basically transport the same (identical) audio data into or out of your PC. Check if the PORT ASSIGN has been made correctly for non-Dante models.The next level for such a multi-channel interface would be a PCIe card like this one from Yamaha *. Check if all the IP addresses are in a compatible range. Check if some other consoles or software are already controlling the devices.
Test with a different switch, or disable IGMP Snooping if you know how. In some rare cases (depending on switch type and device firmware versions) this can block the control data while allowing audio.
Check if the network switch is using a feature called “IGMP Snooping”. The IP address for MIXER CONTROL must be in a different subnet (number range) to the IP address for DEVICE CONTROL. Check the Device ID begins with “Y0**”, where ** is a hexadecimal number between 01 and FF. Check the device firmware is up to date (v4.1 or newer for CL/QL, v1.7.34 or newer for ULXD4, v1.1.15 or newer for QLXD4, 1.16.11 or newer for AXT400). Check the IP address used by the Shure receivers: DEVICE UTILITIES->NETWORK->SHURE CONTROL->NETWORK. If audio is working well but the console is still unable to control the Shure receivers: Please refer to the respective video or documentation guide for the setup.
0 kommentar(er)
